Free tool

Speaker and headphone test

Check that left and right come out of the right side, that both speakers are wired the same way, and how low your bass goes. Switch to Headphones and it works as a headphone test too.

Testing

Turn your system volume down before the first sound, then raise it until the test is easy to hear.

  1. 01 · Left and right

    Each button plays a short burst of noise. It should come only from the side it names, and Center should sit between the two.

    What did you hear?
  2. 02 · Phase

    Both sounds play the same noise from both sides. In A the two sides move together. In B one side is flipped on purpose, the way a speaker wired backwards would sound. Switch between them a few times.

    Which one sounds fuller, with the sound in the middle?
  3. 03 · Bass sweep

    A low tone rises slowly from 20 to 200 Hz. Press I hear it as soon as you can hear or feel it. Keep listening after that: if something buzzes or rattles, press Rattle.

    20 HzReady

What each test tells you

TestGood resultWorth fixing
Left and rightEach burst comes from its own side, and Center sits in the middleSides swapped, one side silent, or both sides playing every burst
PhaseA sounds fuller and centered, B sounds thin and spread outB sounds fuller than A: one speaker is wired backwards
Bass sweepTone appears smoothly and grows without buzzingBuzz or rattle at one frequency, or no tone until well above 100 Hz

The sweep plays the same level at every frequency, but our ears hear low notes as quieter, so the tone seems to swell as it rises. Where you first hear it depends on the volume too. Run it at the level you usually listen at.

How to fix what you find

Left and right are swapped

With speakers, swap the two speakers or the left and right cables at the back of the amp or the powered speaker. With headphones, check that you're wearing them the right way round, since L and R are easy to miss.

Only one side plays

Check the balance first. On Windows, open Settings, then System, Sound, pick your output and look at the Left and Right volume. On a Mac it's the Balance slider in System Settings, then Sound. Then try the other cable or swap the speakers: if the silent side moves with the cable, the cable is the problem. With headphones, a plug that isn't pushed in all the way often plays only one side.

Both sides play every burst

Something is turning stereo into mono. Look for Mono audio in Windows (Settings, Accessibility, Audio) or Play stereo audio as mono on a Mac (System Settings, Accessibility, Audio). A Bluetooth headset that's also being used as a mic can switch to mono call mode, so close any call app and try again.

B sounds fuller than A

One speaker is wired backwards. Turn off the amp, then at one speaker swap the two wires so red goes to red (+) and black to black (−). Speaker wire usually has a stripe, a ridge or text on one side so you can follow it from end to end. Powered speakers that connect with a single fixed cable can't get this wrong.

The sweep rattles at one spot

Hold that frequency with the slider and walk around. It's often a shelf, a picture frame or a loose grille, not the speaker. On headphones, a hair or bit of lint caught under the ear pad can flutter at low notes, and taking the pad off to clear it usually fixes it.

Time for new speakers?

If the sweep stays silent until well past 75 Hz or a rattle won't go away, our guides cover what owners say about speakers and headphones after living with them.

Speaker test questions

Which speaker is the left one?

The one on your left while you sit facing the speakers, in your usual listening spot. With headphones, the left side is usually marked L on the band or inside the earcup.

How do I test left and right on my headphones?

Switch the test to Headphones, put them on and play the left and right sounds. Each one should come only from the side it names. If they're reversed, check that the earcups aren't on backwards. If both sides play every sound, the source is probably sending mono, which a Bluetooth headset in call mode does.

Can I test my subwoofer with this?

Yes, with the bass sweep. With a subwoofer connected, the lowest part of the sweep should come mostly from the sub before the main speakers take over. If the deep notes stay silent, check the sub's power, its volume knob and its crossover setting.

What does out of phase mean?

One speaker's red and black wires are swapped, so its cone moves out while the other moves in. The two cancel each other in the bass, and the sound loses its center. It doesn't damage anything, and swapping the wires back at one speaker fixes it.

Why can't I hear the lowest notes in the sweep?

Small speakers can't move enough air to play deep bass. Many budget bookshelf and computer speakers stop somewhere around 50 to 75 Hz, so a sweep that starts at 20 Hz stays silent for a while. Owners who want more low end usually add a subwoofer.

Can this test damage my speakers?

Not at normal listening levels. Start with the volume low and raise it slowly, especially for the bass sweep. If a woofer starts to buzz or flap, stop and turn it down.

Does it work with Bluetooth and on a phone?

Yes. Bluetooth adds a short delay before each sound, which doesn't change the results. Phone speakers are often mono or too small for bass, so plug in headphones on a phone. A Bluetooth headset that's also being used as a mic may switch to mono call mode, and then left and right sound the same.